|
Issue with rotatortype -180 -> 0 -> +180
|
|
0
|
50
|
June 22, 2026
|
|
SatNOGS Ground Station Antenna and Rotator Hardware Assembly Help
|
|
11
|
254
|
May 25, 2026
|
|
ROTCLD Easycomm Won't Control Rotor, Error -5
|
|
3
|
102
|
May 4, 2026
|
|
Phasma Mission: Ground Station Construction Notes
|
|
2
|
101
|
April 14, 2026
|
|
How test Gpredict antenna algo?
|
|
2
|
120
|
April 13, 2026
|
|
G6LVB (LVB) Tracker case/enclosure
|
|
2
|
99
|
February 28, 2026
|
|
Trying to setup firmware, no luck
|
|
4
|
101
|
February 22, 2026
|
|
CNC Sheild Rotator firmware
|
|
5
|
120
|
February 10, 2026
|
|
SatNOGS Rotator Setup
|
|
0
|
131
|
January 8, 2026
|
|
AlphaSpid Rotor with Hamlib + GPredict
|
|
4
|
174
|
December 16, 2025
|
|
Satnogs rotator firmware and hamlib
|
|
0
|
123
|
October 26, 2025
|
|
New station online - #4386
|
|
3
|
125
|
October 20, 2025
|
|
SatNOGS Rotator v3.1 Build Project
|
|
23
|
2978
|
September 16, 2025
|
|
Assembling a transparent case for a SatNOGS v3 rotator
|
|
1
|
1147
|
August 30, 2025
|
|
SatNOGS rotator v3.1- rotary encoders?
|
|
32
|
1692
|
August 5, 2025
|
|
Outdoorproof and powerful Rotator
|
|
3
|
1551
|
June 4, 2025
|
|
Beginner to SATNOG community a simple way for students to build Satnogs rotator controller or able to buy pre-made one
|
|
6
|
437
|
May 27, 2025
|
|
The Swarm Turret
|
|
0
|
91
|
May 25, 2025
|
|
Satnogs satellite rotators + silent driver tmc2208 for eliminate radio interference
|
|
20
|
1798
|
May 9, 2025
|
|
Rotator works correctly over the LAN , not with SATNOG client
|
|
3
|
71
|
April 2, 2025
|
|
SatNOGS rotator with CNC Shield and ESP8266
|
|
12
|
1254
|
February 27, 2025
|
|
Rotator Controller V2.4 Assembly
|
|
2
|
553
|
December 24, 2024
|
|
Yaesu rotator g5500dc not responding
|
|
1
|
166
|
October 27, 2024
|
|
About coding the rotator
|
|
0
|
77
|
October 19, 2024
|
|
Troubleshooting ROTCTLD Container failure in Docker software
|
|
2
|
154
|
September 24, 2024
|
|
G5600B and Two G450 Rotators Compatibility
|
|
1
|
116
|
September 9, 2024
|
|
Compiling 3.1 sketch for Arduino Uno and CNC shield
|
|
10
|
285
|
August 26, 2024
|
|
H-bridge combination with Yaesu 5500DC controller box?
|
|
6
|
297
|
July 23, 2024
|
|
Yaesu G-5500 through "COM-232B" controller - both azimuth and elevation are way off
|
|
16
|
1028
|
July 13, 2024
|
|
Seeking advice and help to set up my Arduino rotator controller with an H-Bridge to control the speed of my antennas, which use a Yaesu 5500 DC
|
|
1
|
277
|
June 29, 2024
|