|
Satnogs satellite rotators + silent driver tmc2208 for eliminate radio interference
|
|
18
|
1559
|
March 16, 2025
|
|
SatNOGS Rotator v3.1 Build Project
|
|
18
|
482
|
March 8, 2025
|
|
SatNOGS rotator with CNC Shield and ESP8266
|
|
12
|
1025
|
February 27, 2025
|
|
Beginner to SATNOG community a simple way for students to build Satnogs rotator controller or able to buy pre-made one
|
|
1
|
109
|
February 24, 2025
|
|
Rotator Controller V2.4 Assembly
|
|
2
|
478
|
December 24, 2024
|
|
Yaesu rotator g5500dc not responding
|
|
1
|
75
|
October 27, 2024
|
|
About coding the rotator
|
|
0
|
58
|
October 19, 2024
|
|
Troubleshooting ROTCTLD Container failure in Docker software
|
|
2
|
102
|
September 24, 2024
|
|
G5600B and Two G450 Rotators Compatibility
|
|
1
|
90
|
September 9, 2024
|
|
Compiling 3.1 sketch for Arduino Uno and CNC shield
|
|
10
|
173
|
August 26, 2024
|
|
H-bridge combination with Yaesu 5500DC controller box?
|
|
6
|
192
|
July 23, 2024
|
|
Yaesu G-5500 through "COM-232B" controller - both azimuth and elevation are way off
|
|
16
|
470
|
July 13, 2024
|
|
Seeking advice and help to set up my Arduino rotator controller with an H-Bridge to control the speed of my antennas, which use a Yaesu 5500 DC
|
|
1
|
188
|
June 29, 2024
|
|
Gpredict Antenna control Error
|
|
3
|
250
|
June 20, 2024
|
|
Rotor control issue
|
|
34
|
445
|
June 3, 2024
|
|
Advanced rotor settings? No reset, no angle limitation, parking
|
|
9
|
452
|
February 7, 2024
|
|
TWO SATNOGS SATELLITE ROTATORs dancing in syncro
|
|
0
|
382
|
February 2, 2024
|
|
Need Help: Yaesu G5500 DC Setup - Elevation Not Working
|
|
8
|
1029
|
December 19, 2023
|
|
Calibration of the G-5500 rotator
|
|
2
|
583
|
December 19, 2023
|
|
I cloned GPredict w/ VS 2022 and made some changes - now can’t compile. Anyone willing to spare a hand recompiling my code?
|
|
0
|
284
|
November 21, 2023
|
|
Observation stopped after exceeding 180° azimuth
|
|
11
|
867
|
May 4, 2023
|
|
Gpredict and Rotctld problem. AZ & EL reads error message in Rotator controll section
|
|
3
|
797
|
September 13, 2023
|
|
Using PST Rotator shifts rotator fractional decrees with SAT_ROT_THRESHOLD is set to 8
|
|
0
|
317
|
July 18, 2023
|
|
New build of rotator v3?
|
|
0
|
560
|
July 3, 2023
|
|
Yeasu rotor engaging with Gpredict on Linux
|
|
8
|
1223
|
June 12, 2023
|
|
SATNOGS_ROT_THRESHOLD <1 deg for S-Band
|
|
2
|
485
|
May 26, 2023
|
|
Rotator done - eliminated Arduino
|
|
11
|
2949
|
May 21, 2023
|
|
Yaesu G5500DC not engaging automatically - Arduino shield
|
|
0
|
433
|
May 10, 2023
|
|
Why the YAESU G-5500DC do not moove from
|
|
0
|
526
|
May 5, 2023
|
|
Setting up Yaseu G5500 with Ardushield
|
|
9
|
1050
|
April 4, 2023
|